Vcds 12.12 interface not found
- VCDS 12.12 INTERFACE NOT FOUND HOW TO
- VCDS 12.12 INTERFACE NOT FOUND CRACKED
- VCDS 12.12 INTERFACE NOT FOUND PDF
- VCDS 12.12 INTERFACE NOT FOUND INSTALL
GND of 12 V to GND of LM7805, everything works fine during the uploading/flashing procedures.Ħ) after every flashing and verify told me that check was successfull (ok).
VCDS 12.12 INTERFACE NOT FOUND PDF
512b words fw Ĥ) power supply with a proper voltage stabilizer: 12Vĥ) 12V power supply applied to LM7805, GND connected as pdf procedure 6 for 11.11.5-12.12.0 eeprom 512 rl.hex) even if probably is not a 512 ģ) by PonyProg2000 set fuse and bits on security and configuration bits (it should be 256b words), this time I did NOT use v. Hi Matty, I'd like to briefly reply to this previous message you sent me:ġ) why should I remove R51 resistence (also if the cable is working fine?)?Ģ) I updated suggested ept file on ftdi by Mprog īy PonyProg2000 I updated firmware (1.92) + eeprom (vers.
VCDS 12.12 INTERFACE NOT FOUND HOW TO
RE: Help: how to repair vcds china cable 12.10.3 - sgtpepper67 - 09-10-2015 Maybe should I connect the interface to the car now to change it from NOT READY to OK? Tried with both 11.11.5 and 12.12.0 and now license is fully (green color) and test is ok with K1,K2 except CAN:NOT READY, still not ready. I have flashed again the atmega162 with firmware v.1.92 + eeprom vers 6 11.11.5-12.12.0_eeprom 512 rl.hex and used fuse/bits as 320 (not 512). Then go to About and see if its ActivatedĪntivirus to check if you have a virus there.
VCDS 12.12 INTERFACE NOT FOUND INSTALL
Install the vcds software 11.11.5 and/or 12.12.0 I will also reply asap with all the needed info. Now I have re-flashed all again and I have again CAN:NOT READY but immediately after the test I got another message with "license not found".
VCDS 12.12 INTERFACE NOT FOUND CRACKED
If needed, I have included the 11.11.5 cracked software (no need to reflash cable to use).RE: Help: how to repair vcds china cable 12.10.3 - sgtpepper67 - 08-10-2015 Note: For a 12 volt supply, you can either use a benchtop power supply or a 12V battery (such as an Energizer A23 automotive key fob battery) to supply power (+/-12V) to the OBDII connector on your cable for programming.ĬD, DC, F9, CC, FFFFFF56 (it will be obvious once you open eXtreme burner where these go)įYI: It is known that the long coding function does not work in the 12.12.0 cracked software (poor programming).
12V to both Pins 4 & 5 of the OBDII connector and one of the following: Pins 4, 6, 8, or 10 on the USBasp connector Pin 9 connects to Pin 2 of the Atmega chip, or Pin 15 or the MCP2515 chip Pin 7 connects to Pin 3 of the Atmega chip, or Pin 13 of the MCP2515 chip Pin 5 connects to Pin 4 of the Atmega chip (no corresponding pin on MCP2515) Pin 1 connects to Pin 1 of the Atmega chip, or Pin 14 of the MCP2515 chip Pins 4, 6, 8, and 10 are common grounds (you only need to use one of them) flash GAL/ATF (not required for this cable, will not discuss) flash FTDI with Mprog (ept file) over USBģ. Steps: Erase, Program with dumps, Program fuse bits & lock bitsĢ. Note: I prefer eXtreme Burner 1.4.2 with the USBasp AVR Programming Device flash Atmega162 (flash + eeprom) with external programmer Install VCDS (Cracked) and install cracked RT-USB driversġ. Make sure any antivirus/malware program/firewall is NOT running Remove RT-USB.SYS from C:/Windows/System32/drivers Remove RT-USB.dll from C:/Windows/System32 Uninstall any previous versions of VCDS before starting I am only providing the following information for educational purposes!įor all cracked software, I have had the best luck with Windows 7 Ultimate x86. Please support Ross-Tech by buying an original cable! It is a fantastic product!